PAI8 Magnetic Ring Holder: 62 × 2.5 mm Fit Checks

PAI8 has a published size and weight, but a specification sheet is only the starting point. The useful buyer test is whether the ring diameter suits the intended hand, whether the adhesive works on the actual case surface, and whether the folding action remains consistent on the approved sample.

PAI8 uses a folding aluminum-alloy ring body; fit and finish still need approval on the exact sample.
PAI8 uses a folding aluminum-alloy ring body; fit and finish still need approval on the exact sample.

Direct answer: the published PAI8 body is 62 × 2.5 × 39.5 mm, its finished weight is 9.5 g, and its ring inner diameter is 39.5 mm. It uses an aluminum-alloy body with an N52 magnet and a folding ring. The current public product record does not publish a magnetic-force value for PAI8, so a buyer should not infer one from another model or accept a number that has not been measured on the exact sample version.

What each published dimension tells the buyer

The 62 mm length and 39.5 mm width describe the overall format; they do not describe the space available inside the ring. The separate 39.5 mm inner diameter is the value to discuss when testing one- or two-finger grip. The 2.5 mm body dimension affects how the holder sits against a phone or case, while the 9.5 g finished weight gives an initial expectation for pocket carry. Treat all four values as acceptance inputs to re-check on the sample, with tolerances agreed in the inspection plan.

Why the 39.5 mm inner diameter needs a real-hand check

A ring can meet its published inner diameter and still feel wrong if the test uses the wrong finger, orientation or phone weight. Test the intended phone and case together, note whether users are expected to slide one or two fingers through the ring, and record how the phone hangs when carried. Do the test on the actual product revision rather than a similarly shaped model. The PAI8 product page records the model data and should remain the specification source; the sample is the evidence for the physical experience.

Fit the adhesive face to the actual phone or case

PAI8 uses an adhesive mounting face, so the receiving surface is part of the product combination. Record the phone model, case material, back texture, curvature and whether the surface is bare, painted, leather-like or silicone. Clean and install the sample according to the supplier's written procedure, then allow the tape to reach its stated bond before the carrying test. A result obtained on one glossy bare phone should not be transferred to every retail case.

If the buyer intends to sell the holder as a set with a case, test that case. If it will be sold separately, state the application surfaces supported by the approved test set and keep the installation instructions with the product. The buyer answer library covers the difference between a supplier claim and a configuration-specific sample result.

Check the folding action separately from magnetic holding

Open and close the ring through the full intended travel. Record whether it moves smoothly, whether the ring returns to the intended viewing angle, whether there is objectionable side play, and whether the folded position remains stable in a pocket. Keep magnetic holding as a separate check. A good hinge does not prove that the magnet performed as expected, and a strong magnet does not prove that the hinge or adhesive will last.

A repeatable PAI8 sample sequence

StepWhat to doEvidence to keep
1. Identify the versionRecord model, drawing or sample revision, colour and finish.PO reference and sample label
2. Measure the baselineCheck 62 × 2.5 × 39.5 mm, 9.5 g and the 39.5 mm ring inner diameter.Instrument, method and measured values
3. Test the combinationUse the intended phone and case; record the surface and installation method.Photos and a written pass or fail result
4. Test the ring actionOpen, close and test the intended carrying and stand positions.Short video and observations
5. Freeze the approvalKeep the approved sample and note every open tolerance or cosmetic point.Signed record and retained golden sample

When PAI8 should be the first sample

PAI8 is the logical first sample when a folding ring, a thin body and low finished weight matter more than a published magnetic-force figure. A buyer who needs the published force values for comparison should review the CX-5 page and OX-3 page instead of assuming those values belong to PAI8. CX-5 is published at 58 × 3.8 mm and 18 g; OX-3 is published at 58 × 4.5 mm and 25 g. Choice should follow the phone, case, use position and the evidence each model actually publishes.

What the PAI8 record does not establish

It does not establish universal phone or case compatibility, a measured magnetic-force value, or third-party certification. The owner of the requirement should decide which magnetic measurement and surface test are needed for the target market, then record them on the approved sample. Published scope can be checked on the facts page, and the broader approval workflow is in the sample approval checklist.

What to put in the PAI8 sample request

Send the model, quantity, target market, intended phone and case, ring colour, logo artwork, retail packaging requirement and the date the samples are needed. Existing tooling models start at 50 pcs per model. Samples take 7–10 working days after requirements are confirmed; mass production takes 7–12 days after sample approval, followed by 3–5 days for packing and final inspection, FOB Shenzhen.

Need a price for your own model?

Send us your drawing or a reference photo. You will get unit price, sampling time and shipping cost within one working day.

Get a quote See all models

Frequently asked questions

What are the published PAI8 dimensions and weight?

The published PAI8 body is 62 × 2.5 × 39.5 mm, the finished weight is 9.5 g, and the ring inner diameter is 39.5 mm.

Is a magnetic-force value published for PAI8?

No. The current public product record does not publish a magnetic-force value for PAI8. Measure the exact approved sample version instead of transferring a value from another model.

How should the PAI8 adhesive face be tested?

Test it on the intended phone or case surface after cleaning and installing it according to the written procedure. Record the phone, case material, back texture and bond result.

How should a buyer choose between PAI8, CX-5 and OX-3?

Use the published structure and evidence for each model. PAI8 is a 62 × 2.5 × 39.5 mm folding ring at 9.5 g, CX-5 is 58 × 3.8 mm at 18 g, and OX-3 is 58 × 4.5 mm at 25 g. Confirm the phone, case and intended use on samples.

What are the MOQ, sampling and production lead times?

Existing tooling models start at 50 pcs per model. Samples take 7–10 working days after requirements are confirmed; mass production takes 7–12 days after sample approval, followed by 3–5 days for packing and final inspection, FOB Shenzhen.

Models mentioned in this guide

Send us an inquiry

Fill in your details and we will reply with price, sampling time and lead time.

Fields marked * are required.

We reply within one working day, Monday to Saturday.
Sample requests welcome — tell us the model and your market.

Add company, phone and country (optional)
Add quantity, target market and production details (optional)
How did you find us? (optional)

Your details are stored in our own database and sent to our sales team so we can answer your inquiry. We never use them for advertising.

WhatsAppGet a quote